PRODUCTS: MARINE APPLICATION & CUSTOMIZED aiR cONDITIONING

Air Cooled Condensing Units are the most used in Marine Environments. They are left outside facing the offshores waves, hostile corrosive  conditions & explosion threats. Being outside the motor power and control panels are indoors Rig or ships zones. encasement in GI 90 baked on enamel SS304 or SS316L depending on the harshness of the environment and GI 90 baked on enamel for milder onshore conditions. They are supplied Explosion Proof electrical safety switches, junction boxes, terminals and optional HEX compressors and extended 5 years warranty. This range is equipped with gauges, water proof  monitoring and fault pilot lights, engraved mimic operations & safety manual facilitating servicemen tasks. For other models and specific requirements, please refer to Page-7 for selection.

Air Cooled Water Chillers are the most used in Marine Environments. They are left outside facing the offshores waves, hostile corrosive  conditions & explosion threats. Being outside the motor power and control panels are indoors Rig or ships zones. encasement in GI 90 baked on enamel SS304 or SS316L depending on the harshness of the environment and GI 90 baked on enamel for milder onshore conditions. They are supplied Explosion Proof electrical safety switches, junction boxes, terminals and optional HEX compressors and extended 5 years warranty. This range is equipped with gauges, water proof  monitoring and fault pilot lights, engraved mimic operations & safety manual facilitating servicemen tasks.

For other models and specific requirements, please refer to Page-7 for selection.

Water Cooled Water Chillers are validation is like water cooled condensers but with the water-cooling evaporator is incorporated in the set. It usually comes with Semi-hermetic and screw compressors at the higher range.. Chillers can range from 10 to 360 TR.

*Consult with us for your requirement.

Water cooled condensers are usually used on river boats and land installations near riverbeds (less saline & corrosive water) and in geothermal heat rejection. it is used when it is difficult to place near the Air Side equipment, For use in sea water, nickel chrome tubes to be used in the heat exchangers.

*Consult with us for your requirement.  

Remote condensers are used for air cooling air-conditioning equipment where major components ere preferred to remain indoor for convenient access and service. They consist of condensing coils, fans and chassis most likely of stainless steel.

*Consult with us for your requirement.

Packaged Units can provide convenient installation operation in small to medium size platforms. As a unitary unit it encloses the condenser section and the evaporator blower section in one encasement in GI 90 baked on enamel SS304 or SS316L depending on the harshness of the environment. They are supplied with variable setting pully belt single speed or VFD drive motors, built in motor starts and controls, pre-charged and ready to energize.

Standard Models are PAC-020 , PAC-030, PAC-040, PAC-060

For other models and specific requirements, please refer to Page-7 for selection.

Air Handling Units designed for harsh environments and motion resistant and are of SS construction. They can be for normal cooling with temperature and humidity control with vaporizers and reheat, as treatment units and pretreatment fresh air sections, recovery wheels, bag or HEPA filter, mixing sections to a variety of air flow and air pressures with constant or variable speeds and with built in fluid controls as requested.

*Designs and configuration to clients’ requirements 

 Air terminal units are of SS304 construction preset or provided with modulating dampers and can be equipped with electric heaters. Also, available is the fan assisted built and flow control version. Those can be operated with a manual three-position fan speed control and thermostat or with a proportional analog thermostat for speed control.

 Modular Split Units are similar to wall type DX Units but designed for harsh environments and motion. they are of SS304 construction (both indoor & outdoor) and used through Control Cabins, Operators' Cabins, Equipment Rooms, instrumentation rooms, crane cabins, muster(evacuation) areas, labs, enclosed walkways.

*Standard sizes are 2, 3 & 4 RT. Other sizes. Other sizes and ceiling types are available upon request.

Floor standing Coil Units come in oven baked coating on GI90 steel or in brushed SS304 casing. adjustable bi-directional grills. They come complete with a three-way solenoid valve optional modulating valve with corresponding thermostat and fan speed control with easy access for washable filter.

Central Data Centers Precision Control Units are of the hydronic type can be ducted type for point distribution using centrifugal blowers or downward blowing to raised under floor using mixed flow fans. the units are microprocessor controlled and can be linked by SMTP TCP/IP protocol for the data center operators and by BMS for maintenance operations.

Those are designed with stand by power that can pull down the space down to 18% Humidity and 8ºC temperature. They have humidification, De-humification and reheat